11 Hawthorn Parkway
Vernon Hills, IL 60061
CEILING PAINT & PRIMER IN ONE
Vertical Spray Primer & Finish
Generic Type – Acrylic, solvent-base, interior stain blocking primer-sealer & finish coat
Performance Characteristics –
• Quick cure for water stains
• Ideal for common overhead stains
• Matches the color of most ceiling tiles
• Flat white finish won’t yellow
• Low odor aerosol
• May be used as a primer or primer/finish
• Use under or over any latex or oil base paint
Recommended Uses – Apply as a primer/finish to interior acoustic ceiling tiles or painted ceilings, light fixtures, HVAC ductwork &
vents, overhead pipes & conduit, or anywhere an overhead high hiding stain sealing primer or spot finish is needed.
Interior Substrates – New, primed or previously painted ceiling tiles, drywall, cured plaster, cement, stucco, wood (pine, fir, birch,
oak and plywood), aluminum, iron, steel and galvanized metal, PVC, glossy laminates and other interior surfaces.
General Description – Covers UP Ceiling Paint & Primer in One is a low odor aerosol that is a stain killer and ceiling touch-up paint in
one. It seals water damaged ceilings and sprays vertically for ease of use. It’s perfect for touch up when you don’t want to repaint the
entire ceiling due to spot damage. Zinsser’s stain blocking primer technology is incorporated into this new generation product that
offers a flat white finish that matches most new acoustical ceiling tiles and white ceiling paints. Covers UP is an odorless oil-base
formula with only a brief odor from propellants that diminishes quickly.
Stain Killer – One coat will effectively block most water stains, graffiti, nicotine, and smoke stains. If a second coat is desired, allow to
dry two hours before recoating.
Ceiling Paint for Ceiling Tiles – Use to block water, nicotine or smoke stains on ceiling tiles. Dries flat and matches the color of
most ceiling tiles.
Paint or Primer for All Ceilings – Dries flat and will match some white painted ceilings. Use as a stain blocking primer for any ceiling
surface. May be topcoated with ceiling paint in two hours when used as a primer.
Surface Preparation
Surfaces should be clean, dry, sound and free of dust, dirt, excessive chalky material, grime, grease, oil, wax, mildew, wallpaper
adhesive or any contamination that may interfere with adhesion. If unsure, always wash surface with a household ammonia and water
solution, appropriate cleaning solution, or solvent (Do not use TSP as a cleaner). Remove any unsoundly adhered coatings. Sand any
remaining paint film edges smooth with the surface. Attempt to remove existing stains by washing, sanding, scraping, etc. Remove
interior mildew with an interior mildew cleaner. Countersink exposed nail heads, spot-prime and fill with Zinsser Ready Patch
®
spackling
compound. Wire brush rusty areas.
WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. Contact the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
Application Directions – Shake can until ball inside rattles, then continue shaking for one minute. If ball does not rattle, do not strike
can. Repeat shaking periodically during use. Test spray pattern on scrap surface before using. Spray 10-12 inches from surface. Mask
off nearby objects. Apply with short ‘dusting’ strokes. Will seal most stains. When finished, clean valve by holding can upside down and
spraying until clear gas comes out. To clear clogged spray tip, remove from can and clean with pin.
Application conditions – Apply within the following ranges:
Humidity
0% to 85%
40° F to 90°F (4°C to 32°C)
Product # 3688
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais